two years annual rate contract (arc) for the supply of spares for ametek make analyzer - ametek nsl888 p/n200859002 conax gland seal at914004d, cable keyboard to controller,p/n 200878001,for 880-nsl, capacitor xenon-lamp. 2uf 2000v,old p/n:200879001, new p/n:200879001s, xenon lamp p/n200880001, solenoid rotary 15v 45 degrees p/n:200884001, wp. filter band pass 0.5d 232nm for nsl 880, wp. filter band pass 0.5d 280nm for nsl 880, wp. filter band pass 0.5d 254nm for nsl 880, wp. filter band pass 0.5d 400nm for nsl 880, quartz window p/n:a-200887001, viton o ring window seal p/n: 202813026, ametek nsl888 p/n203790001 check valve, aspirator at914004d, fuse micro 250ma, 125v p/n 205223011, fuse micro 1a 125v p/n 205223019, ametek nsl888 p/n251744000 gauge, pressure, dual 200 kpa/30 psig back center mount at914004d, lens,uv fl=50.8mm dia m=38.1mm p/n:257846001, relay solid state 6a 240v p/n:265972001, heater,4x5 rubr 120v 100w,p/n:269168003, ametek nsl880 p/n269323011 temp controller, cal3200 at14014/414014/514014/614003/714 003/814003, fuse, pn:269439019, ametek nsl880 p/n269442023 fuse, 5a (f1) at14014/414014/514014/614003/714 003/814003, ball valve pneumatic actuat p/n269962001, ametek nsl888 p/n273398001 keypad, host interface, sst at914004d, demister rtd for chemtrols air demand analyser(mdl: ametek 888), part no.: 273402001, for sru7, ametek nsl888 p/n273408002 proportional valve at914004d, ametek nsl888 p/n273454002 orifice, division 2 electronic section purge, 200 micron at914004d, ametek nsl888 p/n273455002 orifice, pressure transducer purge, 50 micron at914004d, 24v power supply for chemtrols air demand analyser(mdl: ametek 888), part no.: 273524001, for sru7, ametek nsl888 p/n273530002 vent, x-purge, sst, iecex at914004d, temperature signal converter for chemtrols air demand analyser(mdl: ametek 888), part no.: 273563001, for sru7, ametek nsl888 p/n273700001 check valve, zero flush at914004d, ametek nsl888 p/n273749001 toggle valve at914004d, ametek nsl888 p/n273757001 orifice, trickle purge between aspirator and zero flush valves, 150 micron at914004d, rtd 100 ohms sensor bulb, 2mmx6mm, 3wr, 36" teflon leads, for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 403047001, for sru7, rtd 100 ohms, 1/8" x 2" w., 36" leads, for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 403048001, for sru7, lamp assembly for chemtrols air demand analyser(mdl: ametek 888), part no.: 403225901, for sru7, aspirator, al 3/8 disc 4" long p/n:407300902, cell heater 0.5 kw 110 v ac for nsl880 , p/no: 407464903, amatek nsl880 demister assembly p no:a.880019902, photo diode pcb p/n a880020901, wp.pcb wiring module assy mdl880,p/n:880024901, filter assembly p/n:880033901, rtd exd 18 inch long element 1/8 dia p/n:880041001, rtd exd 7 inch long element 1/8 dia p/n:880041002, window gasket,teflon,p/n a.880042001,for 880:nsl air demand analyser, keypad,p/n:880061001,for 880-nsl, ametek p/n880063001 pad sst 5/8dia 1.5lg demister, p/n:880063001, pad sst 5/8dia 1.5lg demister, p/n:880063901, ms.lamp power supply & trigger,p/n:880118901, demister pad, teflon pn:880136901, ametek nsl880 p/n880271001 o- ring buna 20.0mm id x 4.5mm at14014/414014/514014/614003/714 003/814003, sample cell assembly- complete,p/n:880312902,for 880- nsl, ametek nsl888 p/n883005902 detector cal filter assembly at914004d, ametek nsl888 p/n883010901 assembly, pressure sensors on bracket at914004d, ametek nsl888 p/n883023902 mirror block assembly (measuring cell) at914004d, ametek nsl888 p/n883024912 120 vac, complete heater assembly, with rtds, cartridge and plate, atex/iecex zone 1 at914004d, ametek nsl888 p/n883034902 assembly, high range measuring cell (2.5") at914004d, ametek nsl888 p/n883038902 assembly, 888 pressure transducer with connector at914004d, sensor electronic board for chemtrols air demand analyser(mdl: ametek 888), part no.: 883047901, for sru7, detector board for chemtrols air demand analyser(mdl: ametek 888), part no.: 883048901, for sru7, ametek p/n 883049901 dc/dc converter for ada mdl nsl888 sru7, ametek nsl888 p/n883076901 888 flash lamp lens replacement kit at914004d, cell rtd for chemtrols air demand analyser(mdl: ametek 888), part no.: 883095001, for sru7, flange rtd for chemtrols air demand analyser(mdl: ametek 888), part no.: 883095002, for sru7, ametek nsl888 p/n883097002 gasket, double block sj ball valve at914004d, signal disconnection assembly board for chemtrols air demand analyser(mdl: ametek 888), part no.: 883110901, for sru7, "make: ametek mdl: o2 analyzer 33424je nipple, 316 ss, 3/4"" npt, 3, 1/2"" long,", make: ametek mdl: o2 analyzer:73769ke fiting,pro filter, ametek 931-934-919 p/n01-0024 fuse 1.0a slo-blo pico ii, amatek 919 h2s micro-interface board p no:100-0116, microcontroller board p/n:100- 0117 of h2s analyser ametek model : 919, keypad board p/n:100-0136 of h2s analyser ametek model : 919, host controller board (display interface) p/n:100-0138 of h2s analyser ametek model : 919, amatek 919 h2s pmt buffer board p no:100-0140, power supply, ac/dc, 12v, 40w, switchmode p/no.1000-616-je, ccr#2 lh regn o2 analyser at424383, lcd display, color, 4.2", 1/4 vga, 480 x 272, 3.3v p/no. 1000-617-je, ccr#2 lh regn o2 analyser at424383, ametek 931-934-919 p/n100-0688 lamp magnesium, ametek,pn:1000-751-je controllertag no:331004n, digital i/o module,p/n:1000-752-je for sulphur analyser, model:asoma 682t-hp, make:ametek, analog i/o module , p/n:1000-753- je for sulphur analyser, model:asoma 682t-hp, make:ametek, thermocouple module , p/n:1000- 754-je for sulphur analyser, model:asoma 682t-hp, make:ametek, ametek,pn:1000-755-je battery boardtag no:331004n, ametek,pn:1000-756-je communication moduletag no:331004n, hmi touch screen interface, p/n:1000-757-je for sulphur analyser, model:asoma 682t-hp, make:ametek, tp700 sd card -- ametek p/n: 1000- 762-je for sulphur analyser, model:asoma 682t-hp, make:ametek, s7-1200 series plc sd card ametek p/n: 1000-851-je for sulphur analyser, model:asoma 682t-hp, make:ametek, ametek,pn:1000-904-je battery 3v,cr1025tag no:331004n, ametek 931-934-919 p/n100-0939 pwb display i/o expansion, temparature daughter board p/n:100-1662 h2s analyser ametek model : 919, ametek 931-934-919 p/n100-1214 sample/vent line rtd termination board (zone 1), ametek 931-934-919 p/n100-1215 customer termination board (zone 1), termination board p/n:100-1534 h2s analyser ametek model : 919, ametek 931-934-919 p/n100-1639 assy, heater 120vac for asr / hag probe, ametek 931-934-919 p/n100-1658 assy, heater 240vac for asr / hag probe, optical bench p/n:100-1662 h2s analyser ametek model : 919, host-controller board(lower enclosure) for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 100-1757, for sru7, customer i/o board(lower enclosure) for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 100-1758, for sru7, ac distribution board(lower enclosure) for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 100-1771, for sru7, micro-controller board(upper enclosure) for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 100-1781, for sru7, probe inconel (inner),p/n:1825 ice, optical bench service electronics board(upper enclosure) for chemtrols h2s analysers(mdl: ametek 931), part no.: 100-1841, for sru7, ametek 931-934-919 p/n100-1868 software m919ae host- controller, o ring, size 125, baked teflon coated aflas p/n:100-1911 of h2s analyser ametek model : 919, customer connection board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-1971, for sru7, power supply assembly for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-1983, for sru7, ametek 931-934-919 p/n100-2006 assy o-ring kit [baked] aflas adjustable length cell, ametek 931-934-919 p/n100-2009 o- ring baked aflas size 125, mcu board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2045, for sru7, analog board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2047, for sru7, pwb detector interface board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2048, for sru7, display interface board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2049, for sru7, relay board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2050, for sru7, xenon lamp power supply board for chemtrols h2s/hc/air- demand analysers(mdl: ametek ips4/888), part no.: 100-2061, for sru7, signal disconnection board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2076, for sru7, ac disconnection board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2077, for sru7, fiber filter element p/n:100-2193 h2s analyser ametek model : 919, ametek 931-934-919 p/n100-2194 assy fiber filter hag probe, ametek 931-934-919 p/n100-2195 assy fiber filter ss hag probe, ametek 931-934-919 p/n100-2212 assy o-ring kit baked aflas for adjustable length cell, micro-interface board(upper enclosure) for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 100-2231, for sru7, ametek 931-934-919 p/n100-2373 ic programmed with m93xs mc software - low byte (u405), ametek 931-934-919 p/n100-2374 ic programmed with m93xs mc software - high byte (u407), ametek 931-934-919 p/n100-2375 ic programmed with m931s/934s hc software, ametek 931-934-919 p/n100-2503 assy cell 81.2cm ss, 9xx hot/wet apps [for spare parts], ametek p/n 100-2613 mdl 934 tcd for sru7 h2 analyser ai914401, ametek 931-934-919 p/n100-2631 assy tc h2 sensor calibrated m931/932 atex, ametek ips-4 p/n100-2633 assy pressure transducer 100psia , ss with welded stub ai914012, ametek 931-934-919 p/n100-2674 pca, m9xx eeprom [for use with hc v4.00 or higher] read-only memory 64k (8k x 8), ametek 931-934-919 p/n100-2683 pca, self-powered isolated v-i converter, rohs compliant, "xenon lamp for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2761 and 100-, 1994, for sru7", ametek ips-4 p/n100-2832 pca dual bench detector interface, ips-4 ai914012, infrared source assembly interface board for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2838, for sru7, ametek ips-4 p/n100-2842 o-ring karlez (wetted o-rings only) ai914012, ametek ips-4 p/n100-2844 assembly, motor, stepper for ips- 4 ir bench ai914012, infrared lamp for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 100-2847, for sru7, ametek ips-4 p/n100-2872 pca ndir preamp board ips-4 ai914012, ametek ips-4 p/n100-2952 o-ring, karlez , #014 ai914012, ametek 931-934-919 p/n100-3014 power supply pca for m93x/241, 4 dc outputs, ametek ips-4 p/n100-3081 o-ring [baked] viton size 2-027 ai914012, heater cartridge 150watt 120vac,p/n:11069je, heater cartridge, p/n 11080je ametek wdg iv o2 analyser, "ametek o2 analyzer p/n11086je, .heater,cart,1/2"",200w @ 230v", "over heat thermostat,p/n, :14113je,at-32306 & at-32307 o2 analyser, model : wdg iv, make : ametek", ametek, calibration filter for nsl880 ada, p/n:200095002s, ac414014/514014, sru2/3, retainer ring,30mm aperture p/n:200555001, valve ball spring-rtrn 1/4 tb, p/n:200852002, fuse micro 50ma,125v p/n 205223006, wiring board fuse 1/4a,125v p/n:25270je, battery, p/n 25352je, wdg-v, rtd - box temp control - 100 ohm (o2 only), p/n:25384je, ametek-o2-stack- overtemperature fuse, power supply,iq link,wall mount,pn:25509je for ametek wdg hp ii iq oxygen analyser., ametek o2 analyzer p/n25550je display,vac. fluorescent,intelligent,4 line x 20 char.,lcd, ametek o2 analyzer p/n25588je sensor,temp,gas stream,for uop apps,1000 ohm rtd (flow rtd), fuse, pn:269439024, amatek 919 h2s beam splitter p no:300-0271, cell window, fused silica p/n:300- 0281 of h2s analyser ametek model : 919, amatek 919 h2s pmt steering mirror p no:300-0283, filter interference 228.8 nm per dwg, p/n 300-0994, h2s 919 analyzer, cup pmt for chemtrols h2s analysers(mdl: ametek 931), part no.: 300-1520, for sru7, o-ring for optical bench filter, for chemtrols analysers(mdl: ametek 931), part no.: 300-1528, for sru7, plate pmt for chemtrols h2s analysers(mdl: ametek 931), part no.: 300-1622, for sru7, cadmium lamp part no. 300-2070 of h2s analyser ametek model no. 919 or equivalant., amatek 919 h2s reflecting mirror p no:300-2179, ametek 931-934-919 p/n300-2360 o- ring silicone 2-016, amatek 919 h2s o-ring for reflecting mirror/beam splitter/lamp p no:300- 2361, aspirator non- relieving pressure regulator, 60 psig out, 1/4"npt, for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 30 0-2823, for sru7, ametek 931-934-919 p/n300-2883 relay solid state 10 amp, ametek 931-934-919 p/n300-3214 fuse micro fast acting 200ma 125v radial, ametek 931-934-919 p/n300-3389 clip in.cin. 1in. for optic. filters, ametek 931-934-919 p/n300-4189 fuse 0.800 a 250v time delay 5 x20mm, "photomultiplier tube lg pmt low gain <(><<)>1500 alm,p/n 300-, 4342,h2s 919 analyzer", ametek 931-934-919 p/n300-4548 fuse gma 2a 250v f/b 5 x 20mm csa/ul approved, ametek 931-934-919 p/n300-4586 cartridge heater csa/ul 240v 100w 60in. high temp leads 1/2in. dia 2.5in. length, o-ring, silicone 2-014 p/n:300-4651 h2s analyser ametek model : 919, ametek 931-934-919 p/n300-4753 fuse gma 1a 250v f/b 5 x 20mm csa/ul approved, ametek 931-934-919 p/n300-4869 ssr relay spst-no 260vac 1a 5 volt coil tht dip-16, ametek 931-934-919 p/n300-4913 tip rtd series 900, amatek 919 h2s oven rtd p no:300-4924, ametek 931-934-919 p/n300-4926 insert aspirator euro teflon, filter interference 326 nm per dwg,p/n 300-4927, h2s 919 analyzer, "ametek 931-934-919 p/n300-4934, transducer pressure 0-30 psia 0- 100mv o/p c/w 36in. cable", o-ring, viton size 008 p/n:300-4958 h2s analyser ametek model : 919, ametek 931-934-919 p/n300-5557 fuse 400ma s/b 5x20mm csa/ce/ul approved, ametek 931-934-919 p/n300-5705 valve solenoid model 6011- 2/2way 240v/60hz/4w nc, photomultiplier tube mg pmt medium gain 1500 alm - 2000 alm, p/n 300- 5771, h2s 919 analyzer, ametek 931-934-919 p/n300-5790 fuse gma 1/8a 125ma 5 x 20mm, o-ring for sov base block, aflas, for chemtrols analysers(mdl: ametek 931/934), part no.: 300- 6241, for sru7, o-ring, aflas, size 115 p/n:300-6242 h2s analyser ametek model : 919, ametek 931-934-919 p/n300-6288 window & mirror for white cell assy, ametek 931-934-919 p/n300-6289 mirror white cell as per drawing 300-6289, ametek 931-934-919 p/n300-6292 fuse fst 1.6a 250v s/b 5x20, ametek 931-934-919 p/n300-6328 filter power 30a 125/250v, ametek 931-934-919 p/n300-6368 filter 10a 115/230 2-stage, ametek 931-934-919 p/n300-6373 relay solidstate 240v 25a, ametek 931-934-919 p/n300-6542 window cell fused silica, ametek 931-934-919 p/n300-8491 valve solenoid model 331-3/2way 240vac (+/-10%) 50/60hz 8w csa ul ce, amatek 919 h2s over temparature switch p no:300- 8637, amatek 919 h2s heater cartridge, 120v, 150w p no:300-8684, o-ring, aflas, size 121 p/n:300-8719 h2s analyser ametek model : 919, amatek 919 h2s silicone o-ring (heater assembly) p no:300-8721, o-ring, aflas, size 118 p/n:300-8722 h2s analyser ametek model : 919, ametek 919 h2s analyser sample/vent isolation ball valve, stop valve asr900 probe,p/n:300- 8731, ametek 919 h2s analyser sample/vent isolation ball valve, extension valve handle,p/n;300- 8732, "ametek 931-934-919 p/n300-8742 heater cartridge 240vac 150w 32in. high temp leads 1/2in. dia, 2.5in. length", ametek 931-934-919 p/n300-8777 fuse 5x20mm 63ma 250v time delay, ametek 931-934-919 p/n300-8778 fuse 5x20mm 125 ma 250v time- delay, ametek 931-934-919 p/n300-8899 kit o-ring asr900 probe, o-ring for sov adaptor fitting, for chemtrols analysers(mdl: ametek 931/934), part no.: 300- 8914, for sru7, rtd 100 ohms sensor bulb, 36" leads, for chemtrols h2s/h2 analysers(mdl: ametek 931/934), part no.: 300-9236, for sru7, solenoid valve, 2-way, part of solenoid block(sol a/b/z) for chemtrols h2s/h2/hc analysers(mdl: ametek 931/934/ips4), part no.: 300- 9242, for sru7, ametek 931-934-919 p/n300-9244 fuse fst 1a, 250v s/b 5x20, ametek ips-4 p/n300-9461 window sapphire 1.5" x 1/4" ai914012, ametek 931-934-919 p/n300-9524 fuse 5x20mm 32ma 250v fast acting, ametek 931-934-919 p/n300-9541 probe tube, 1/2" sch 40, 48" long, 316l, amatek 919 h2s sample/vent isolation ball valve assembly kit p no:300- 9824, solenoid valve, 3-way, part of solenoid block(sol a/b/z) for chemtrols h2s/h2/hc analysers(mdl: ametek 931/934/ips4), part no.: 300- 9827, for sru7, ametek 931-934-919 p/n300-9839 fuse 2a 250v 5x20 s/b csa, ul, vde, sev, semko approved, ametek 931-934-919 p/n300-9847 fuse (pico) 300-315 ma slow blow, ametek 931-934-919 p/n300-9917 spacer cell 0.25mm for 1.0mm cell, ametek 931-934-919 p/n300-9977 flowmeter gas 2- 18 scfh ss with needle valve & viton o-rings, amatek 919 h2s hag probe jacket p no:301-0269, lithium coin battery cell external temperature(mcu board), for chemtrols h2s/hc analysers(mdl: ametek ips4), part no.: 301-0382, for sru7, solenoid valves for chemtrols air demand analyser(mdl: ametek 888), part no.: 301-0424, for sru7, pressure regulator, range: 0-30 psig, for chemtrols air demand analyser(mdl: ametek 888), part no.: 301-0430, for sru7, pressure regulator, range: 0-100 psig, for chemtrols air demand analyser(mdl: ametek 888), part no.: 301-0431, for sru7, ametek ips-4 p/n301-0462 cartridge heater 400w 120vac 1/2"dia x 8.5"l, csa certified ai914012, ametek ips-4 p/n301-0577 keyboard front panel ips-4 ai914012, ametek ips-4 p/n301-0701 display vacuum fluorescent graphic module for ips-4 ai914012, ametek,pn:301-0860 fuse 1 a time delay 5 x 20mm ccctag no:at914012, ametek ips-4 p/n301-0861 fuse 2a time delay 5 x 20mm ccc ai914012, ametek ips-4 p/n301-0862 fuse 4 a time delay 5 x 20mm ccc ai914012, ametek ips-4 p/n301-0863 fuse 6.3a time delay 5 x 20mm ccc ai914012, ametek ips-4 p/n301-0929 rtd 1/8" x 20" ai914012, reed relay, shielded, 12v dc coil, no contact, for chemtrols h2s/hc analyser(mdl: ametek ips4), part no.: 301-1353, for sru7, ametek 931-934-919 p/n301-1422 valve check 1/3 psig 1/4in. tube x 1/8in. npt with aflas oring, ametek 931-934-919 p/n301-1634 power supply 24 vdc c/w harness for m9xx, amatek 919 h2s power supply unit(5 and 15 v dc) p no:301-1635, ametek 931-934-919 p/n301-1712 plate filter hag probe ss large dia membrane, sintered disk, 52mm diameter p/n:301-1713 h2s analyser ametek model : 919, high flow filter membrane c/w buna o-ring p/n:301-1714 h2s analyser ametek model : 919, ametek ips-4 p/n301-2666 kit rebuild valve used on asr/hag probe with double block ai914012, ametek ips-4 p/n301-4756 power supply,12v 100 watts ai914012, ametek ips-4 p/n301-4839 teflon washer, cell window (retainer gasket) ai914012, ametek ips-4 p/n301-4851 window, 0 .43 od x 0.195 protrusion, sapphire, 5/8"od x .125 ai914012, ametek ips-4 p/n301-5107 bearing, 5mm x 16mm x 5mm ai914012, ametek ips-4 p/n301-5160 bearing, self aligning, 5mm double shielded abec ai914012, ametek ips-4 p/n301-5165 mirror, gold 25.4mm x 6.35mm ai914012, ametek ips-4 p/n301-5305 valve solenoid 12vdc 2-way hnbr seal material c/w 100mm leads ai914012, ametek ips-4 p/n301-5373 filter, 1 inch, narrow band 3498nm +/- 30 nm ai914012, ametek o2 analyzer p/n33072je nipple,1/8npt,hex,ss, ametek,pn:36021je valve, check, 1 psi cracking psr, 1/4" t on both endtag no:at24383/at424383, valve,solenoid(aspirator air),p/no:36022,pan, valve,solinoid(caliberation gas),p/no:36023, solenoid valve,oxygen span gas,pn:36034je for ametek wdg hp ii iq oxygen analyser., gauge,air regulator,pno:37013 for o2 analyser ametek wdg iv, ametek,pn:37018je .gauge,0-60 psi,1-1/2" diatag no:at24383/at424383, meter,flow,p/no:37030 for o2 ana.,pan tach en, regulator,air,pno:39003 for o2 analyser ametek wdg iv, ametek,pn:39004je filter/regulator,0-60 psi, 1/4" ports, inlet 0-250tag no:at24383/at424383, 'o' ring electrochemical cell, p/n 42005je ametek wdg v - oring,metal,ss,0.812 od, "ametek,pn:42152je, .gasket,inconel,3"",300#tag no:at24383/at424383", o-ring for insitu cell, part no.42244je, module display p/n:42373je,, wdg-v rear plate ,ke gasket,p/n:7000-314, ametek o2 analyzer p/n7000-330- se assy, lcd host interface pcb and guard, ametek o2 analyzer p/n7000-351- ke overlay, key pad, host interface, cell standard 4 1/4 p/n:7000-568- se wdg-v o2 analyser, ametek,pn:7000-691-se assy, sample out weldment– uop isolation valvetag no:at24383/at424383, ametek,pn:7000-692-se assy, sample in weldment –uop isolation valvetag no:at24383/at424383, assy furnace 120vac p/n:7000-719- se wdg-v o2 analyser, kit flow sensor p/n:7000-817-te wdg-v o2 analyser, wdg-v ,replacement thermocouple kit for o2 cell furnace p/n:7000-839-te, wdg-v- 115 vac heater coil and push nut replacement kit- p/n:7000-840-- te, "wdg-v, box heater assy , 120vac, ,p/n:7000-843-se", kit, cartridge heater, 350w, p/no.120v7000-846-te, ccr#2 lh regn o2 analyser at424383, ametek o2 analyzer p/n7000-865- te kit, 80520se iq board and plate with eproms, ametek o2 analyzer p/n7001-133- se assy, lcd host interface pcb and guard, atex, kit aspirator p/n: 7001-216-se wdg-v o2 analyser, kit flame arrestor loop p/n:7001- 225-te wdg-v o2 analyser, wdg-v upper door, ke gasket,p/n:7001-659, wdg-v lower door, ke gasket,p/n:7001-660, rtd flow switch, p/n 72684se wdg iv ametek o2 analyser, ametek,pn:7002-134-se assy, furnace, wdg-v uop, 115vac , hast ctag no:at24383/at424383, ametek,pn:7002-166-se wdg-v uop main board assembly with platetag no:at24383/at424383, ametek o2 analyzer p/n7002-487- se assy, wdg-v, sgx boards and plate for rtd comb. he, ferro ceramic filter, p/n 70172se, ametek o2 analyzer p/n70358ue flashback assy,xp,assm, "ametek,pn:70384le, .block,alum,finned,machinedtag no:at24383/at424383", furnace assy,pno:70409se for o2 analyser ametek wdg iv, furnace assem. in/out ss tube assem., flame arrestor, p/n 70487se, ametek o2 ccrg anz cell uop p/n70597se, cell housing -uophastelloyc part no no 70678se for ccr unit, ametek o2 analyzer p/n70725ke probe, 3 ft, threaded,ss,1/8p, ametek o2 analyzer p/n70726ke probe,4 ft, threaded,ss,1/8p, triac,electronic component,p/n:bcr16pm, zirconium oxide cell,p/n.70949ke,o2 analyser, ametek o2 analyzer p/n71014se cell housing assy, hp sensor & high dewpoint, inconel, heater block assy p/n:71016ke, filter, ceramic, w/ra330 bushing & inconel perforated sheath, pn:72171se for ametek wdg hp ii iq oxygen analyser, zirconium cell and seal,pn:71063se, ametek o2 analyzer p/n71072se ferro filter assy, metal probe, 30 micron, filter ceramic with ra330 bushing,p/n:71041se, ametek o2 analyzer p/n71093se manifold block assy,ss,cv,o2, flashback assemb 1" element p/n:71212se wdg-v o2 analyser, ametek o2 analyzer p/n71294ke probe, 3ft, 310ss,threaded,1/8p, ceramic probe for o2 analyser,at 23103/423103u=1050mm,od=19mm, id=13mm, max temp=1200 deg.c, 3/8" npt(m) inst.side and 3/4" npt(m) pr ocess side, four feet inconel probe size 10 mm od x 7 mm id,p/n.71295ke,02 analyser, wdg hp gasket p/n:71672ke, thermocouple,type:k,pno:71697ke for o2 analyser ametek wdg i, washer (ceramic),part no.71715ke, "ametek,pn:71764se, .deflector,wdg-institu filtertag no:at-380-03-4002", o2 gasket, flange, wdg 1210 institu ametek thermox p/n 71780ke, insulating tube, mullite,part no.71782ke, zirconia cell p/n 71785se for ametek wdg210 oxygen analyser, o2-cpp-washer, ceramic - notched wdg 1210 institu ametek thermox p/n 71848ke, ametek,pn:71849se .filter assy,wdg insitutag no:at-380-03- 4002, ametek,pn:71861se .flame arrestor,wdg-insitutag no:at- 380-03-4002, ametek,pn:71862se .filter & shield assy, insitutag no:at-380-03-4002, ametek,pn:71863se .filter&flame arrestor,wdg insitag no:at-380- 03-4002, "ametek o2 analyzer p/n71920se, .tube,inside,3/4'insitu", ametek o2 analyzer p/n71921se tube,inside,1.5'insitu, "ametek,pn:71923se, .tube,inside,6'insitu,sparetag no:at-380-03-4002", outside clip with 2 ft. of wire p/n 72328se wdg iv ametek, opto,electronic component,p/n:1l410, filter(20 micron) for wdg insitu pn : 74422se , ceramic with shield, ametek o2 analyzer p/n72681se assy,hook,uop flow switch, zirconia cell assembly ccr uop o2 analyser wdg v uop-rp-7002-004- ke, ametek o2 analyzer p/n72865ke probe,t316ss,threaded,2ft, heater thermocouple assembly - 18 inch, p/n:73051te, ametek o2 analyzer p/n73050te kit,htr/tc rpl,12"lg,75w,115v, heater/thermocouple assy,36'', p/n 73052te f/ametek wdg210 oxygen analyser, ametek,pn:73053te .kit,htr/tc rpl,78"lg,75w,115vat-380-03-4002, ametek purge sov for instiu 2000 probe part no 73489, filter, ,p/n:73770se,at-32306 & at- 32307 o2 analyser, model:wdg iv, make : ametek, board,iq sensor main,pn:73938se for ametek wdg hp ii iq oxygen analyser., ametek,pn:75133ke assy, tube, exhaust, 11" hast c, uop/rptag no:at24383/at424383, ametek o2 analyzer p/n75675se assy, furnace, 5", wdg, atex, ametek,pn:76181ke probe hast c 1/4" npt x 18"tag no:at24383/at424383, ametek,pn:76417te wdg-1200 power and data connectorstag no:at-380-03-4002, ametek,pn:76418te wdg-1210 probe to controller connectorstag no:at-380-03-4002, ametek,pn:76512se assy, control unit, series 1200 insitutag no:at- 380-03-4002, ametek,pn:76722se assy, hook/rtd, uop w/flow switch, hast ctag no:at24383/at424383, probe ss310, threaded, 42" p/n:76798ke wdg-v o2 analyser, assy pcb main processor p/n:8000- 119-se wdg-v o2 analyser, wdg-v, peripheral i/o board,p/n:8000-120-se, amevision circuit board for chemtrols air demand analyser(mdl: ametek 888), part no.: 8000-122-se, for sru7, pcb, asy, host display, customer connection board p/no. 8000-123- se, ccr#2 lh regn o2 analyser at424383, microprocessor board, p/n 80342se, sensor board,pn:80418se for zr.oxyde analyser, card assembled cal/memory, p/n:80436se, controller power supply pcb p/n a80438se, backplane assy.,p/no:80439 for o2 ana.,pan te, board,processor,p/no:80440se for o2 ana.,pan te, "expansion pc board, ,p/n:a.80449se,for air demand analyser,mdl:880nsl,ametek make", board,wiring,p/no:80457 for o2 ana.,pan tech, sensor board,p/no. 80471se, board sensor p/n: 80485se, ametek o2 analyzer p/n80521se assy,pc,dig-ma module,iq sensors, board,iq sensor,rcu module,pn:80522se for ametek wdg hp ii iq oxygen analyser, ametek o2 analyzer p/n80523se card,rs-485 comm module,iq sensors, ametek,pn:80585se display pcbtag no:at-380-03-4002, ametek,pn:80586se assy, power supply, series 1200 control sectiontag no:at-380-03-4002, programmed eprom,p/n:880060901s,for 880-nsl, uv cutoff filter,p/n:880103001, 15 v dc power supply(120v ac) p/n:880107901s for 880-nsl, ametek nsl880 p/n880107902s 15v dc power supply (240v ac) at14014/414014/514014/614003/714 003/814003, valve sol 2wy exed 1/4npt 120v, p/n:880108912s, valve sol 3wy exed 1/4npt 120v,p/n:a.880108913s, ametek nsl880 p/n880108914s 2- way solenoid valve, 240v at14014/414014/514014/614003/714 003/814003, ametek nsl880 p/n880108915s 3- way solenoid valve, 240v at14014/414014/514014/614003/714 003/814003, valve rev 3wy exed 1/4npt 120v,p/n:880108916s, ametek nsl880 p/n880108917s 3- way solenoid valve, 240v (steam b/b) at14014/414014/514014/614003/714 003/814003, controller power supply assembly,p/n:880114901s,for 880- nsl, display/cpu/prom module assy,p/n:880115901s, thermistor sensor pc assy, p/n:880122901s, "ametek o2 analyzer p/n88015qe, .assy,eprom,u5,main module", filter arm,p/n:880303001, ametek nsl888 p/n883026904s 888 demister pad kit: includes sst pads (qty: 2) and teflon pads (qty: 2) at914004d, ametek nsl888 p/n883057901s programmed, amevision board (host display board), serial number required at914004d, ametek nsl888 p/n883064901s battery, fuse, and varistors kit at914004d, ametek nsl888 p/n883065901s measuring cell rebuild kit, 888: includes o-rings (qty: 10), gaskets (qty: 10), quartz windows (qty: 2) at914004d, module,display,p/no:90219ve, module,power supply/keypad,p/no:90253ve,pan tec, spare part kit, p/n 95001ve, kit for wdg instu pn: 95344 ve, probe-complete ss310,36",pn:95349we, ametek o2 analyzer p/n95350we kit,probe w/filt.cv/hp,310ss,24", ametek o2 analyzer p/n95351we kit,probe w/filt.cv/hp ss,48", "ametek o2 analyzer p/n95382we, .kit,insitu cell leads 3/4'", ametek,pn:95385we .kit,insitu cell leads 6'tag no:at-380-03-4002, board,main logic,p/no:pc104/hc900/b, ametek asoma p/nps-0082 pwr supply, 24v 2.5 a rail mnt 331004n, rail mounted 24v 2.5a power supply, p/n:ps0088 for sulphur analyser, model:asoma 682t-hp, make:ametek, set of orings, p/n:rg-0001/rg- 0008 for sulphur analyser, model:asoma 682t-hp, make:ametek, ametek asoma p/nrg-0008 o-ring, 030 epdm 331004n, aspirator block with heater, p/n 70600ue, ametek-o2-stack-assy, aspirator, wdg3, flow switch inlet tube with rtd, p/n 72147ve for wdg iv, "back plane pcb,, old p/n:880112901, new p/n:880112901s"